Home » SWITCH 642-813 Q&As » Section 6 - Mix Practice Q&As » 642-813 Q&A – Mix Practice Questions (131-135)

642-813 Q&A – Mix Practice Questions (131-135)

Section 6 – Mix Practice Questions

QUESTION NO: 131
hostname Switch1
interface Vlan10
ip address 172.16.10.32 255.255.255.0
no ip redirects
standby 1 ip 172.16.10.110
standby 1 timers 1 5
standby 1 priority 130
hostname Switch2

interface Vlan10
ip address 172.16.10.33 255.255.255.0
no ip redirects
standby 1 ip 172.16.10.110
standby 1 timers 1 5
standby 1 priority 120
HSRP was implemented and configured on two switches while scheduled network maintenance was
performed.
After the two switches have finished rebooting, you notice via show commands that Switch2 is the HSRP
active router. Which two items are most likely the cause of Switch1 not becoming the active router?
(Choose two.)
A. this is normal operation
B. IP addressing is incorrect
C. standby group number does not match VLAN number
D. incorrect standby timers
E. incorrect priority commands
Answer: A

QUESTION NO: 132
Refer to the exhibit. From the configuration sample shown of a Cisco Catalyst 3560 Series Switch,
what can you determine regarding Layer 3 routing functionality of the interface?

132
A. The interface is configured correctly for Layer 3 routing capabilities.
B. The interface needs an additional configuration entry to enable IP routing protocols.
C. The interface subcommand ip routing is required to enable IP routing on the interface.
D. An SVI interface is required to enable IP routing for network 192.20.135.0.
Answer: A

QUESTION NO: 133
You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have assigned that interface to VLAN 20. To check the status of the SVI, you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an “up/up” state. What must be true in an SVI configuration to bring the VLAN and line protocol up?
A. The port must be physically connected to another Layer 3 device.
B. At least one port in VLAN 20 must be active.
C. The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.
D. Because this is a virtual interface, the operational status will always be in an “up/up” state.
Answer: B

QUESTION NO: 134
Refer to the exhibit. From the configuration shown, what can you determine about the private VLAN configuration?
134
A. Only VLAN 503 will be the community PVLAN because multiple community PVLANs are not allowed.
B. Users of VLANs 501 and 503 will be able to communicate.
C. VLAN 502 is a secondary VLAN.
D. VLAN 502 will be a standalone VLAN because it is not associated with any other VLANs.
Answer: C

QUESTION NO: 135
Refer to the exhibit. From the configuration shown, what can be determined?
135

A. The sticky addresses will only be those manually configured MAC addresses enabled with the sticky keyword.
B. The remaining secure MAC addresses will be dynamically learned, converted to sticky secure MAC addresses, and added to the running configuration.
C. Since a voice VLAN is configured in this example, port security should be set for a maximum of 2.
D. A security violation will restrict the number of addresses to a maximum of 10 addresses per access
VLAN and voice VLAN. The port will be shut down if more than 10 devices per VLAN attempt to access the port.
Answer: B

Lead2pass Testking Pass4sure Actualtests Others
$99.99 $124.99 $125.99 $189 $29.99-$49.99
Up-to-Dated
Real Questions
Error Correction
Printable PDF
Premium VCE
VCE Simulator
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back

One thought on “642-813 Q&A – Mix Practice Questions (131-135)

Comments are closed.