Section 6 – Mix Practice Questions
QUESTION NO: 106
Which of the following HSRP router states does an active router enter when it is preempted by a higher priority router? (Select the best answer.)
A. active
B. speak
C. learn
D. listen
E. init
F. standby
Answer: B
QUESTION NO: 107
Which of these is true regarding the configuration and application of port access control lists?
A. PACLs can be applied in the inbound or outbound direction of a Layer 2 physical interface.
B. At Layer 2, a MAC address PACL will take precedence over any existing Layer 3 PACL.
C. When you apply a port ACL to a trunk port, the ACL filters traffic on all VLANs present on the trunk port.
D. PACLs are not supported on EtherChannel interfaces.
Answer: C
QUESTION NO: 108
A campus infrastructure supports wireless clients via Cisco Aironet AG Series 1230, 1240, and 1250 access points. With DNS and DHCP configured, the 1230 and 1240 access points appear to boot and operate normally; however, the 1250 access points do not seem to operate correctly. What is the most likely issue causing this problem?
A. DHCP with option 150
B. DHCP with option 43
C. PoE
D. DNS
E. switch port does not support gigabit speeds
Answer: C
QUESTION NO: 109
Refer to the exhibit. On the basis of the information that is generated by the show commands, which two EtherChannel statements are true? (Choose two.)
A. Interfaces FastEthernet 0/1 and 0/2 have been configured with the channel-group 1 mode desirable command.
B. Interfaces FastEthernet 0/3 and 0/4 have been configured with the no switchport command.
C. Interface Port-Channels 1 and 2 have been assigned IP addresses with the ip address commands.
D. Port-Channels 1 and 2 are providing two 400 Mbps EtherChannels.
E. Port-Channels 1 and 2 are capable of combining up to 8 FastEthernet ports to provide full-duplex bandwidth of up to 16 Gbps between a switch and another switch or host.
F. Switch SW1 has been configured with a Layer 3 EtherChannel.
Answer: AD
QUESTION NO: 110
Refer to the exhibit. Which configuration on the HSRP neighboring device ensures that it becomes the active HSRP device in the event that port fa1/1 on Switch_A goes down?
A. Switch_B(config-if)# ip address 10.10.10.2 255.255.255.0
Switch_B(config-if)# standby 1 priority 200
Switch_B(config-if)# standby 1 preempt
Switch_B(config-if)# standby 1 ip 10.10.10.10
Switch_B(config-if)# standby 1 track interface fa 1/1
B. Switch_B(config-if)# ip address 10.10.10.2 255.255.255.0
Switch_B(config-if)# standby 1 priority 200
Switch_B(config-if)# standby 1 ip 10.10.10.10
C. Switch_B(config-if)# ip address 10.10.10.2 255.255.255.0
Switch_B(config-if)# standby 1 priority 195
Switch_B(config-if)# standby 1 preempt
Switch_B(config-if)# standby 1 ip 10.10.10.10
D. Switch_B(config-if)# ip address 10.10.10.2 255.255.255.0
Switch_B(config-if)# standby 1 priority 190
Switch_B(config-if)# standby 1 ip 10.10.10.10
Switch_B(config-if)# standby 1 track interface fa 1/1
Answer: C
