Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 61 Refer to the exhibit. What is the result of setting GLBP weighting at 105 with lower threshold 90 and upper threshold 100?
Continue reading
April 27, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 56 Refer to the exhibit. Both routers are configured for the Gateway Load Balancing Protocol (GLBP). Which statement is true?
Continue reading
April 26, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 51 In what three states is it possible for an HSRP router to be in? (Select three) A. Standby B. Established C. Active D. Idle E. Backup F. Init Answer: ACF
Continue reading
April 26, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 46 On a 3550 EMI switch, which three types of interfaces can be used to configure HSRP? (Select three) A. Loopback interface B. SVI interface C. Routed port D. Access port...
Continue reading
April 25, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 41 Which statement best describes Cisco supervisor engine redundancy using Stateful Switchover? A. Redundancy provides fast supervisor switchover for all Cisco Catalyst 6500 series switches. B. Switchover ensures that Layer 2...
Continue reading
April 25, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 36 HSRP has been configured between two Pass4sure devices. Which of the following describe reasons for deploying HSRP? (Select all that apply) A. HSRP provides redundancy and fault tolerance B. HSRP...
Continue reading
April 21, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 31 Which describes the default load balancing scheme used by the Gateway Load Balancing Protocol (GLBP)? A.per host basis using a round-robin scheme B.per host basis using a strict priority scheme...
Continue reading
April 21, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 26 Refer to the exhibit. Both routers are configured for the Gateway Load Balancing Protocol (GLBP). Which statement is true?
Continue reading
April 20, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 21 Refer to the exhibit. What is the configuration an example of?
Continue reading
April 20, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 16 Which two statements are true about the Hot Standby Router Protocol (HSRP)? (Choose two.) A.Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers. B.Load sharing...
Continue reading
April 19, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 11 On a 3550 EMI switch, which three types of interfaces can be used to configure HSRP? (Choose three.) A.loopback interface B.SVI interface C.routed port D.access port E.EtherChannel port channel F.BVI...
Continue reading
April 19, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 6 Which one of the statements below correctly describes the Virtual Router Redundancy Protocol (VRRP), which is being used in the Pass4sure network to provide redundancy? A. A VRRP group has...
Continue reading
April 18, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As
Section 5 – Implement High Availability, given a network design and a set of requirements QUESTION NO: 1 In which three HSRP states do routers send hello messages? (Choose three.) A.standby B.learn C.listen D.speak E.active Answer: A D E
Continue reading
April 18, 2011 admin
Section 5 - High Availability, SWITCH 642-813 Q&As